The EasySolar combines a MPPT solar charge controller, an inverter/charger and AC distribution in one enclosure. The product is easy to install, with a minimum of wiring. Simply connect the battery cables and solar cables and you’re done!
The EasySolar unit incorporates the following hardware in a single enclosure:
Up to three strings of PV panels can be connected to three sets of MC4 (PV-ST01) PV connectors.
Victron MPPT Solar Controller
The MultiPlus, as the name suggests, is a combined inverter and charger in one elegant package. Its many features include a true sine wave inverter, adaptive charging, hybrid PowerAssist technology, plus multiple system integration features.
The AC distribution consists of a RCD (30 mA/16 A) and four AC outputs protected by two 10A and two 16A circuit breakers. One 16A output is controlled by the AC input: it will switch on only when AC is available.
Unique PowerAssist technology protects the utility or generator supply from being overloaded by adding extra inverter power when needed.
The Color Control GX is the communication-centre of your installation. It offers at-a-glance live information, and lets you control all products connected to it. Full system control is gained - almost anywhere in the world - by accessing your Color Control GX using our free-to-use Victron Remote Management Portal. At a single touch, Color Control GX provides an instant overview of your system: battery state of charge; present power consumption; power harvest from PV; power provision from mains/generator.Victron Remote Management (VRM) provides you with full access to the very extensive controls and settings of all system-components which are connected to either your CCGX or Venus GX. It allows remote user and installer login - from anywhere, at anytime. This powerful application also provides for hassle-free diagnostic checks and analysis of archived information. The Color Control GX can be programmed to auto-start your generator - triggered by low-voltage; high-demand; or battery state of charge. It can be further tailored to delay ignition until the end of 'quiet' periods - avoiding accidental nuisance at dead of night.A Remote Console feature is available. It's like carrying the front face of your CCGX control panel around on your phone, or other device.
The Victron VRM Portal gives a comprehensive analysis of the Power produced from the solar, information of the battery status and the information of the power consumed by the devices connected to the system.
The Victron VRM Portal gives a comprehensive analysis of the Power produced from the solar at a given point of time on a daily basis and comparison between the power consumed by devices in 3 different phases and the total power consumption.
The Victron VRM Portal allows you to set alarm points for all the devices connected to the system. Alarms can be set for Voltage, Current, Temperature, System Failure and Status of Charge of the batteries. If say for example the status of charge on the batteries goes below the pre-set level, a sounder and flasher get activated on the monitor and an email is sent to the registered email address notifying the user of the fault. The same principle applies for all the other parameters as well.
There is a GPS tracker installed in the Monitor which allows the user to track the whole system. The VRM portal has an option to set a perimeter from the location of the system. This is called a GeoFence and the user will be notified if the system is moved outside the designated perimeter.
With the help of a remote console login, you can check the status of all the devices connected to the System. The remote console also gives you an idea of the amount of power the devices are consuming and the amount of power generated by the solar panels.
The remote console also helps you to set the alarm points for each device connected to the system.
A versatile rail, Z-module and splice kit eliminates the need for onsite cutting, making SolarRoof a safe and cost effective PV mounting system.
Designed as a univarsal PV mounting system, SolarRoof is compatible with most of the major framed and frameless PV modules on the market.
With a full range of roof hooks and brackets, this system is suitable for most roofing types, including pitched tile roofs, metal roofs, concrete roofs and even slate roofs.
Strict quality control in accordance with ISO 9001 over materials and finished products ensures optimum strength and long life for your installation.
Clenergy provides a 10 year product warranty for your peace of mind.